Acrylic vs Polycarbonate vs PETG vs PVC
The four clear-sheet plastics people ask us about most, side by side. Values are typical for each material family; grades and brands vary, so ask us if a number is critical to your job.
| Property | AcrylicPMMA, Plexiglas, AcryliteShop acrylic | PolycarbonateLexan, MakrolonShop polycarbonate | PETGCo-polyester, VIVAKShop PETG | PVCRigid PVCShop PVC |
|---|---|---|---|---|
| Impact strength | Moderate | Very high | High | Good |
| Impact strength | About 10× glass (typical) | About 250× glass: practically unbreakable (typical) | High: much tougher than acrylic, though not as tough as polycarbonate (typical) | Moderate: tougher than acrylic, brittle in the cold (typical) |
| Max service temperature | About 80 °C (175 °F) | About 115–120 °C (240–250 °F) | About 65 °C (150 °F) | About 60 °C (140 °F) |
| Clarity / light transmission | About 92% light transmission: the clearest of the four | About 88% light transmission | About 88–90% light transmission | Opaque (grey) only: we don't stock clear PVC |
| Scratch resistance | Good: the most scratch-resistant of the four; light scratches polish out | Poor: scratches easily unless hard-coated | Fair: softer than acrylic, scratches more easily | Fair |
| Bending & thermoforming | Line-bends well with a strip heater; thermoforms at about 150–180 °C. Too brittle to cold-bend. | Cold-bends on a brake in thin gauges; thermoforms after pre-drying (moisture causes bubbles) | Easiest of the four: thermoforms at low temperature with no pre-drying, and cold-bends | Heat-bends and thermoforms readily |
| Gluing | Water-thin solvent cement (Weld-On 3/4) or thickened cement (Weld-On 16); clear, strong joints | Solvent cement for polycarbonate or a structural adhesive; joints are prone to stress-crazing | Solvent cement made for PETG/co-polyester, or adhesives | PVC solvent cement (strong, welded joints) or hot-air welding |
| Laser cutting | Yes: the best laser material, with flame-polished edges | No: burns and yellows, poor edge and harmful fumes | Not recommended: melts, rough edge | Never: releases chlorine gas |
| Outdoor / UV | Excellent: UV stable, doesn't yellow | Good in UV-protected grades | Limited: not UV stabilised | Fair: fades, gets brittle |
| Food contact | Not sold for food contact | Not sold for food contact | Not sold for food contact | Not sold for food contact |
| Typical uses | Displays, signs, picture framing, sneeze guards, lighting, cases and boxes | Machine guards, security glazing, skylights, riot shields, outdoor signs | Retail displays, thermoformed parts, guards and sneeze guards, point-of-purchase | Chemical tanks, ducts, fume hoods, plating and lab fabrication |
| Relative price | $$ (2 of 4) | $$$ (3 of 4) | $$ (2 of 4) | $$ (2 of 4) |
Typical values for general-purpose grades. Impact and price are relative to each other. “Food-contact grades available” means certified grades exist, not that every sheet we stock is certified; ask us before you order.
Which One Should I Choose?
- Choose acrylic for the best clarity and a glossy, scratch-resistant finish: displays, signs, framing, and anything you want to laser-cut.
- Choose polycarbonate when it must not break: machine guards, security glazing and outdoor panels (UV grade). Not for the laser.
- Choose PETG for thermoformed or cold-bent parts and tough indoor displays that need to be clear and cheaper than polycarbonate.
- Choose PVC for chemical resistance: tanks, ducts and lab fabrication. Never laser-cut it.
Every Sheet Material at a Glance
Want to filter instead? Use the material finder.
| Material | Clear | Opaque colours | Outdoor / UV | High impact | Laser-safe | Food-safe | Hockey & rink boards | Cutting boards | Max temp (typical) |
|---|---|---|---|---|---|---|---|---|---|
| Acrylic | Clear: yes | Opaque colours: yes | Outdoor / UV: yes | High impact: no | Laser-safe: yes | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~80 °C (175 °F) |
| Acrylic mirror | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: yes | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~80 °C (175 °F) |
| Polycarbonate | Clear: yes | Opaque colours: yes | Outdoor / UV: yes | High impact: yes | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~115–120 °C (240–250 °F) |
| Twinwall polycarbonate | Clear: yes | Opaque colours: no | Outdoor / UV: yes | High impact: yes | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~115–120 °C (240–250 °F) |
| PETG | Clear: yes | Opaque colours: no | Outdoor / UV: no | High impact: yes | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~65 °C (150 °F) |
| PVC | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~60 °C (140 °F) |
| Foamed PVC | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~60 °C (140 °F) |
| ABS | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: yes | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~80 °C (175 °F) |
| Styrene | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~70 °C (160 °F) |
| HDPE | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: yes | Laser-safe: no | Food-safe: yes | Hockey & rink boards: yes | Cutting boards: yes | ~80 °C (175 °F) |
| UHMW | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: yes | Laser-safe: no | Food-safe: yes | Hockey & rink boards: yes | Cutting boards: yes | ~80 °C (175 °F) |
| Polypropylene | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~100 °C (212 °F) |
| Corrugated plastic | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~80 °C (175 °F) |
| Acetal | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~90 °C (195 °F) |
| Nylon | Clear: no | Opaque colours: yes | Outdoor / UV: no | High impact: yes | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~90–100 °C (195–210 °F) |
| PTFE | Clear: no | Opaque colours: yes | Outdoor / UV: yes | High impact: no | Laser-safe: no | Food-safe: no | Hockey & rink boards: no | Cutting boards: no | ~260 °C (500 °F) |
Not Sure Which Plastic Fits Your Job?
Tell us what you're making and where it's going. We'll suggest a material and quote it. We usually reply the same business day, and always within one business day.